 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz Typical Applications The HMC615LP4E is ideal for: * PCS / 3G Infrastructure * Base Stations & Repeaters * WiMAX & WiBro Features High Input IP3: +35 dBm Low Input LO Drive: -2 to +6 dBm Low Conversion Loss: 10 dB Single Positive Supply: +5V @ 65 mA RoHS Compliant 4x4 mm QFN Package 9 MIXERS - HIGH IP3 - SMT * ISM & Fixed Wireless Functional Diagram General Description The HMC615LP4(E) are high linearity, GaAs FET converter ICs that operate from 2.3 to 4.0 GHz and deliver a +35 dBm input third order intercept point. The LO amplifier output and high dynamic range mixer input are positioned so that an external LO filter can be placed in series between them. The IC operates from a single +5V supply consuming 65 mA of current and accepts a LO drive level of -2 to +6 dBm. The design requires no external baluns and supports IF frequencies between DC and 1 GHz. The HMC615LP4(E) is pin for pin compatible with the HMC551LP4(E), HMC552LP4(E) and HMC215LP4(E), which operate from 0.8 to 4.0 GHz. For availability on Non-RoHS HMC615LP4 products please contact Hittite Microwave sales directly. Electrical Specifi cations, TA = +25 C, LO = 4 dBm, Vcc = +5V, IF = 200 MHz* Parameter Frequency Range, RF, LO Frequency Range, IF Conversion Loss * Noise Figure (SSB) LO to RF Isolation LO to IF Isolation * IP3 (Input) 1 dB Compression (Input) LO Drive Input Level (Typical) Supply Current (Icc) 5 1 Min. Typ. 2.3 - 4.0 DC - 1.0 10 10 15 10 35 21 -2 to +6 65 75 13 Max. Units GHz GHz dB dB dB dB dBm dBm dBm mA *Unless otherwise noted, all measurements performed as a downconverter confi gured as shown in application circuit. 9 - 364 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz Conversion Gain vs. Temperature @ LO = 4 dBm 0 Isolation @ LO = 4 dBm 0 -5 CONVERSION GAIN (dB) -5 ISOLATION (dB) +25C +85C -40C -10 -15 -20 -25 RF to IF LO to RF LO to IF -10 -15 9 3 3.5 4 4.5 -20 1.5 2 2.5 3 3.5 4 4.5 -30 1.5 2 2.5 FREQUENCY (GHz) FREQUENCY (GHz) Conversion Gain vs. LO Drive 0 LO= -4 dBm LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm LO= 6 dBm Return Loss @ LO = 4 dBm 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 LO RF -5 -10 -15 -20 1.5 2 2.5 3 3.5 4 4.5 -30 1.5 2 2.5 3 3.5 4 4.5 FREQUENCY (GHz) FREQUENCY (GHz) Upconverter Performance (IF= 100 MHz) Conversion Gain vs. LO Drive 0 LO= -4 dBm LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm LO= 6 dBm IF Bandwidth @ LO = 4 dBm 0 CONVERSION GAIN (dB) -5 RESPONSE (dB) -5 Conversion Gain Return Loss -10 -10 -15 -15 -20 -20 1.5 -25 2 2.5 3 3.5 4 4.5 0 0.5 1 1.5 2 2.5 FREQUENCY (GHz) FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 365 MIXERS - HIGH IP3 - SMT CONVERSION GAIN (dB) HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz Input IP3 vs. Temperature @ LO = 4 dBm 50 Input IP3 vs. LO Drive 50 40 40 IP3 (dBm) 30 + 25C + 85C - 40C IP3 (dBm) 30 9 MIXERS - HIGH IP3 - SMT 20 20 LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm LO= 6 dBm 10 10 0 1.8 2.2 2.6 3 3.4 3.8 4.2 0 1.8 2.2 2.6 3 3.4 3.8 4.2 FREQUENCY (GHz) FREQUENCY (GHz) Input IP2 vs. Temperature @ LO = 4 dBm 50 Input IP2 vs. LO Drive 50 40 40 IP2 (dBm) 30 IP2 (dBm) 30 20 + 25C + 85C - 40C 20 LO= -2 dBm LO= 0 dBm LO= 2 dBm LO= 4 dBm LO= 6 dBm 10 10 0 1.8 2.2 2.6 3 3.4 3.8 4.2 0 1.8 2.2 2.6 3 3.4 3.8 4.2 FREQUENCY (GHz) FREQUENCY (GHz) Input P1dB vs. Temperature @ LO = 4 dBm 30 25 P1dB (dBm) 20 15 +25C +85C -40C 10 1.7 2.1 2.5 2.9 3.3 3.7 4.1 FREQUENCY (GHz) 9 - 366 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz MxN Spurious @ IF Port nLO mRF 0 1 2 3 4 0 xx 5 58 98 99 1 -11 0 67 102 99 2 -1 16 55 103 104 3 6 37 51 82 106 4 10 36 60 91 107 Harmonics of LO nLO Spur @ RF Port LO Freq. (GHz) 1 1.8 2.6 3.4 4.2 5 1 8 5 11 15 7 16 2 13 23 12 16 18 27 3 29 18 27 48 27 38 4 31 34 30 27 27 43 9 MIXERS - HIGH IP3 - SMT 9 - 367 RF Freq. = 3 GHz @ -10 dBm LO Freq. = 2.8 GHz @ 0 dBm All values in dBc relative to the IF power level. LO = 0 dBm All values in dBc below input LO level measured at RF port. Typical Supply Current Vcc +5.0 Icc (mA) 62 mA For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz Absolute Maximum Ratings RF / IF Input (Vcc= +5V) LO Drive (Vcc= +5V) BIAS Junction Temperature Continuous Pdiss (T = 85C) (derate 5.21 mW/C above 85C) Thermal Resistance (junction to ground paddle) Storage Temperature +27 dBm +10 dBm +7 Vdc 150C 0.339 W 192 C/W -65 to +150C -40 to +85C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 9 MIXERS - HIGH IP3 - SMT Operating Temperature Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC615LP4 HMC615LP4E Package Body Material Low Stress Injection Molded Plastic[4] RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H615 XXXX H615 XXXX [2] [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX [4] For availability of Non-RoHS HMC615LP4 products please contact Hittite Microwave sales directly. 9 - 368 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz Pin Descriptions Pin Number Function Description Interface Schematic 1 MIX LO This pin is DC coupled and matched to 50 Ohms. An off chip DC blocking capacitor is required. 2, 6 - 9, 11 - 17, 19 - 24 N/C No connection. These pins may be connected to RF ground. Performance will not be affected. 9 MIXERS - HIGH IP3 - SMT 9 - 369 3 BIAS Power supply for the LO amplifier. Three external bypass capacitors are recommended for optimum performance, as illustrated in the application circuit. 4 GND Backside of package has exposed metal ground paddle that must also be connected to ground. 5 LO This pin is DC coupled and matched to 50 Ohms. An off chip DC blocking capacitor is required. 10 IF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source/sink more than 18 mA of current or die non-function and possible die failure will result. 18 RF This pin is DC coupled and matched to 50 Ohms. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz Application Circuit 9 MIXERS - HIGH IP3 - SMT Recommended Components Values (IF = DC - 300 MHz) C3 C4 C1, C2, C5 L1 R1 1000 pF 2.2 F 100 pF 18 nH 18 Ohm 9 - 370 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC615LP4 / 615LP4E v01.0407 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 2.3 - 4.0 GHz Evaluation PCB 9 MIXERS - HIGH IP3 - SMT List of Materials for Evaluation PCB 113722 [1] Item J1 - J3 J4, J5 C1, C2, C5 C3 C4 L1 R1 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 100 pF Chip Capacitor, 0402 Pkg. 1000 pF Chip Capacitor, 0603 Pkg. 2.2 F Capacitor, Tantalum 18 nH Chip Inductor, 0603 Pkg. 18 Ohm Resistor, 1210 1/8 watt Pkg. HMC615LP4E 113417 Evaluation Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 371 |
Price & Availability of HMC615LP4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |